1756-IB32 PDF

Give us a call at or We can help you with your Revision specific needs. Close What is New Surplus? Close What is Surplus New? Surplus New - New unused and includes all sub-assemblies and documentation. Close What is Reconditioned?

Author:Meziran Kazijinn
Country:Senegal
Language:English (Spanish)
Genre:Sex
Published (Last):13 June 2014
Pages:123
PDF File Size:13.8 Mb
ePub File Size:3.5 Mb
ISBN:487-8-28073-402-3
Downloads:93921
Price:Free* [*Free Regsitration Required]
Uploader:Akinos



To view it, visit www. This module mounts in a ControlLogix? This module uses one of the following RTBs:? When using an IFM, consult the documentation that came with it to connect all wiring. Before you install your module, you should have already:?

Follow these guidelines when you handle the module:? Touch a grounded object to discharge static potential. Wear an approved wrist-strap grounding device. Do not touch the backplane connector or connector pins. Do not touch circuit components inside the module. If available, use a static-safe work station. When not in use, keep the module in its static-shield box. This module is designed so you can remove and insert it under backplane power and field-side power.

When you remove or insert a module while field-side power is applied, you may cause an electrical arc. An electrical arc can cause personal injury or property damage because it may:? Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connector.

Worn contacts may create electrical resistance. When you insert or remove the module while backplane power is on, or you connect or disconnect the RTB with field-side power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is non-hazardous before proceeding. It has been designed and tested to meet the following directives. For specific information required by EN , see the appropriate sections in this publication, as well as the following Allen-Bradley publications:?

Industrial Automation Wiring and Grounding Guidelines, publication Automation Systems Catalog, publication B This equipment is classified as open equipment and must be installed mounted in an enclosure during operation as a means of providing safety protection.

Install the Module You can install or remove the module while chassis power is applied. However, when you remove or insert an RTB with field-side power applied, unintended machine motion or loss of process control can occur.

Exercise extreme caution when using this feature. Locking tab 1. Align circuit board with top and bottom chassis guides. Key positions on the module that correspond to unkeyed positions on the RTB. For example, if you key the first position on the module, leave the first position on the RTB unkeyed. Key the Module 1.

Insert the U-shaped band as shown. Push the band until it snaps in place. Insert the wedge-shaped tab with rounded edge first. Push the tab until it stops.

Wedge-shaped tab U-shaped bands —M —M Reposition the tabs to rekey future module applications. Spring Clamp RTB 1. Insert the screwdriver into the inner hole of the RTB. Cage Clamp RTB 1.

Insert the wire into the open terminal. Turn the screw clockwise to close the terminal on the wire. Insert the wire into the open terminal and remove the screwdriver.

The example below shows how to wire the module. All terminals with the same name are connected together on the module. When you daisy chain to other RTBs, always connect the daisy chain to the terminal directly connected to the supply wire, as shown in the example above.

This wiring example shows a single voltage source. If separate power sources are used, do not exceed the specified isolation voltage. After completing field-side wiring, secure the wires in the strain relief area with a cable-tie. Align the grooves at the bottom of the housing with the side edges of the RTB. Slide the RTB into the housing until it snaps into place.

It is recommended that field-side power be removed before installing the RTB onto the module. Align the side and top, bottom RTB guides with the side, top and bottom module guides.

Module guide RTB guides —M 2. Press quickly and evenly to seat the RTB on the module until the latches snap into place. Locking tab —M 3. Slide the locking tab down to lock the RTB onto the module. The "OK" indicator turns red for 1 second and then turns to flashing green if it has passed the self-test. The module has passed internal diagnostics but is not multicasting inputs. Previously established communication has timed out. An unrecoverable error has occurred on the module.

The input is active. Take this action: None OK Configure the module. Replace the module. None This completes installation of the module. Use the information below to remove the module. Shock hazard exists. If the RTB is removed from the module while the field-side power is applied, the module will be electrically live.

Failure to observe this caution may cause personal injury. It is recommended that field-side power be removed before removing the module. Before removing the module, you must remove the RTB. Unlock the locking tab at the top of the module. Push in top and bottom locking tabs. Pull module out of the chassis. Use this conductor category information for planning conductor routing as described in the system level installation manual. Refer to publication Additional Notes The ControlLogix system must be mounted within a suitable enclosure to prevent personal injury resulting from accessibility to live parts.

The interior of this enclosure must be accessible only by the use of a tool. This industrial control equipment is intended to operate in a Pollution Degree 2 environment, in overvoltage category II applications, as defined in IEC publication A, at altitudes up to meters without derating. Each product is supplied with markings on the rating nameplate indicating the hazardous location temperature code.

Combinations of equipment in your system are subject to investigation by the local Authority Having Jurisdiction at the time of installation. Do not disconnect equipment unless power has been removed or the area is known to be nonhazardous. Do not disconnect connections to this equipment unless power has been removed or the area is known to be nonhazardous.

Secure any external connections that mate to this equipment by using screws, sliding latches, threaded connectors, or other means provided with this product.

Substitution of components may impair suitability for Class I, Division 2. If this product contains batteries, they must only be changed in an area known to be nonhazardous.

ASTM C1363 PDF

Allen-bradley ControlLogix 1756-OA16 Manuals

.

ALBERTO MARINI MIENTRAS DUERMES PDF

ControlLogix Modules

.

Related Articles